UniFi Switch - Pro AV
Pro AV on UniFi Switches uses Quality of Service (QoS) to automatically optimize traffic for specific audio and video environments by matching and prioritizing latency sensitive traffic. Configure Pro AV on individual ports using the Port Manager.
Requirements
* 7.1.16 is available on the Early Access release channel.
Pro AV is supported on the following switch models:
- USW-Pro-Max-16
- USW-Pro-Max-16-PoE
- USW-Pro-Max-24
- USW-Pro-Max-24-PoE
- USW-Pro-Max-48
- USW-Pro-Max-48-PoE
- USW-EnterpriseXG-24
- USW-Enterprise-48-PoE
- USW-Enterprise-24-PoE
- USW-Pro-24
- USW-Pro-24-PoE
- USW-Pro-48
- USW-Pro-48-PoE
- USW-Pro-Aggregation
Audio and Video Environments
When configuring Pro AV, select the option that matches your setup and the port(s) where audio and video devices are connected. Ports are configure individually for Pro AV and the options do not need to match on the same switch. The following options are available:
- Dante Audio - Matches Audinate Dante audio, PTP and control traffic.
- Q-SYS Audio and Video - Matches Q-SYS audio, video, PTP and control traffic.
- Q-SYS Video with Dante Audio - Matches Q-SYS video with Audinate Dante audio, PTP and control traffic.
- Shure Audio - Matches Shure audio, PTP and control traffic.
- Crestron Audio and Video - Matches Crestron audio, PTP, video and control traffic.
- AES67 Audio - Matches AES67 audio, PTP and control traffic.
- SDVoE with AES67 Audio - Matches SDVoE with AES67 audio, PTP and control traffic .
- SDVoE with Dante Audio - Matches SDVoE with Audinate Dante audio, PTP and control traffic.
- NDI with AES67 Audio - Matches NDI with AES67 audio, PTP and control traffic.
- NDI with Dante Audio - Matches NDI with Audinate Dante audio, PTP and control traffic.
How is Traffic Prioritized when using Pro AV?
Traffic is prioritized by matching on specific DSCP and CoS values, protocols and UDP/TCP ports. Traffic is assigned to a queue which determines priority over other traffic.
IGMP Settings - Snooping, Fast Leave and Querier
It is recommended to enable IGMP Snooping and define a specific switch as the querier. Multicast Filtering (IGMP Snooping) can be enabled for specific VLANs using the Network settings. Refer to the table below for the settings for each environment.
| Environment | IGMP Snooping | Fast Leave | Querier | Unknown Multicast Traffic |
| Dante | Required | Recommended | Must be Present | Do not Forward |
| Q-SYS | Required | Required (NV-32-H) | Must be Present | Do not Forward |
| Shure | Required | Recommended | Must be Present | Do not Forward |
| Crestron | Required | Recommended | Must be Present | Do not Forward |
| AES67 | Required | Recommended | Must be Present | Do not Forward |
| SDVoE | Required | Required | Must be Present | Do not Forward |
| NDI | Required | Recommended | Must be Present | Do not Forward |
It is recommended to manually configure the Querier Switch for each VLAN. Either automatically set the address or manually define it. The switch with the lowest address will be elected as querier.
Note: Fast Leave can also be referred to as Immediate Leave and Unknown Multicast Traffic can be referred to as Unregistered Multicast Flooding.
Custom QoS
Next to Pro AV, it is also possible to create custom QoS entries on the switches listed above in order to match and prioritize traffic. Multiple entries can be created and traffic is prioritized according to the specified queue number. The following options are available:
- Match Type - Match on a specific DSCP or IP Precedence value. None matches on all traffic regardless of value.
- Remark Traffic - Optionally remark matched traffic with a specific DSCP or CoS value. If not specified, forwarded traffic keeps its originally set value.
- Queue - Assign matched traffic to a queue in order to prioritize it over other traffic. The queue range is 0 to 7 with 0 being the lowest priority.
Note: Pro AV and custom QoS cannot be used simultaneously on the same port.