×

UniFi - USW Leaf: CLI Command Comparison

Overview

This article lists the different CLI commands supported by the USW-Leaf switch and their equivalent command on a Cisco switch.

NOTE:The commands with asterisks (*) below are not fully supported yet, and may change without notice.

Table of Contents

1. General Commands

2. VLAN Commands

3. Port Operation Commands

4. LAG (Link Aggregation) Commands

5. SPAN (Port Mirroring) Commands

6. Storm Control Commands

7. Port Isolation (Protected Port) Commands

8. Flow Control Commands

9. QoS (Scheduling, Shaping and Policing) Commands

10. ACL Commands 

11. STP; RSTP Commands

12. MSTP Commands

13. Port Error Disable / Auto Recovery Commands

14. DHCP Guard / DHCP Snooping (Cisco)

15. ARP

16. DHCP Client/Static IP

17. IP Route(Static)

General Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Show OS version information. show version show version
Show base MAC address. show system show version
Show USW Model. show platform info show version
Show current configuration (DRAM). show running-config
show running-config
Show startup configuration (NVRAM). show startup-config
show startup-config
Show all logs that the router has in its memory. show log show log
Overview all IPv4 interfaces on the switch. show ip interface brief
show ip interface brief
Display current routing protocols. show ip protocol
show ip protocol
Display IPv4 routing table. show ip route show ip route
Display IPv6 routing table. show ipv6 route show ipv6 route
Display access list. show access-list <list_name>
show access-list
Display MAC addresses table. show platform mac address-table
show mac address-table
Show ARP table. show arp show arp
Display all users connected to the switch. NA  show users
Display all info about flash memory. NA show flash
Display history of commands used. NA show history
Display the system clock. NA  show clock
Information about hardware status. show environment show environment
Show the amount of switch free memory. show memory show memory

VLAN Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Display VLAN information, all ports which belong to specific VLAN, and information about the number of VLANs configured on the switch. UBNT# show bridge-domain SW# show vlan
Create new VLAN 2. UBNT# configure terminal
UBNT(config)# bridge-domain 2
UBNT(bridge-domain)# exit
UBNT(config)#
SW# configure terminal
SW(config)# vlan 2
SW(config-vlan)# exit
  • Add VLAN 2 membership to the port swp1, configure the native VLAN ID 10.
  • NPOS operates VLAN inside bridge-domain, so it's necessary to associate port with VLAN in bridge-domain.
UBNT(config)# interface swp1
UBNT(config-if)# switchport mode trunk
UBNT(config-if)# switchport trunk allowed vlan 2
UBNT(config-if)# switchport trunk native-vlan 10
UBNT(config-if)# exit
UBNT(config)# bridge-domain 2
UBNT(bridge-domain)# vlan 2 swp1
UBNT(bridge-domain)# exit
UBNT(config)# bridge-domain 10
UBNT(bridge-domain)# vlan 10 swp1
UBNT(bridge-domain)# exit
SW(config)# interface fa1/0
SW(config-if)# switchport mode trunk
SW(config-if)# switchport trunk allowed vlan add 2
SW(config-if)# switchport trunk native vlan 10
SW(config-if)# exit
  • Remove VLAN 2 membership from port swp1 and the native VLAN.
  • NPOS port with VLAN association to bridge-domain is removed automatically.
UBNT(config)# interface swp1
UBNT(config-if)# switchport trunk allowed vlan remove 2
UBNT(config-if)# no switchport trunk native-vlan
UBNT(config-if)# exit
SW(config)# interface fa1/0
SW(config-if)# switchport trunk allowed vlan remove 2
SW(config-if)# no switchport trunk native vlan
SW(config-if)# exit
Enable or disable dot1q tagging for native VLANs on specific port. Cisco's method operates dot1q native tagging globally. UBNT(config)# vlan do1q tag native
UBNT(config)# interface swp1
UBNT(config-if)# vlan dot1q tag native
UBNT(config-if)# no vlan dot1q tag native
UBNT(config-if)# exit
SW(config)# vlan do1q tag native
SW(config)# no vlan do1q tag native
  • Configure the swp1 interface as a nontrunking nontagged single-VLAN 3 access mode.
  • Before switching, disable the current mode.
UBNT(config)# interface swp1
UBNT(config-if)# no switchport
UBNT(config-if)# switchport mode access
UBNT(config-if)# switchport access vlan 3
UBNT(config-if)# exit
UBNT(config)# bridge-domain 3
UBNT(bridge-domain)# vlan 3 swp1
UBNT(bridge-domain)# exit
SW(config)# interface fa1/0
SW(config-if)# switchport mode access
SW(config-if)# switchport access vlan 3
SW(config-if)# exit
Remove any configuration specific to Layer 2 on this interface (include VLAN's membership), switch interface to Layer 3 mode. UBNT(config)# interface swp1
UBNT(config-if)# no switchport
UBNT(config-if)# exit
SW(config)# interface fa1/0
SW(config-if)# no switchport
SW(config-if)# exit
  • Disable MAC address learning on a specified VLAN 2.
  • Maximum number of learning MAC records equal 1000.
  • Configure a secure sticky MAC address for interface swp1.
UBNT(config)# bridge-domain 2
UBNT(bridge-domain)# no learning enable
UBNT(bridge-domain)# learning limit 1000
UBNT(bridge-domain)# learning sticky aa:bb:cc:dd:11:22 interface swp1
UBNT(bridge-domain)# exit
SW(config)# no mac-address-table learning vlan 2
SW(config)# mac-address-table limit vlan 2 maximum 1000
SW(config)# interface fa1/0
SW(config-if)# switchport port-security mac-address aa:bb:cc:dd:11:22
SW(config-if)# exit

Port Operation Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Show port status and admin state. UBNT# show interface status
SW# show interface status
Verify the FEC feature status on the interface.
UBNT# show fec status
 
View the interface status of interface swp1. UBNT# show port status swp1
UBNT# show interface swp1
SW# show interface fa1/0
Display interface statistics. UBNT# show statistics interface
SW# show interface counters
Clear interface statistics counters. UBNT# show statistics clear
SW# clear counters
Display information about the connected transceivers. UBNT# show interface transceiver swp1
UBNT# show platform fwd interface sfp
SW# show interface transceiver
*Information about the switchport interface. NA
show interface switchport
Configure interface speed 100g, autonegotiation, and FEC cl-91. UBNT(config)# interface swp54
UBNT(config-if)# speed 100g
UBNT(config-if)# autonegotiation enabled
UBNT(config-if)# fec cl-91
UBNT(config-if)# exit
SW(config)# interface fa1/0
SW(config-if)# speed 100g
SW(config-if)# speed auto
SW(config-if)# fec cl91
SW(config-if)# exit
Configure maximum transmission unit (MTU) size per specific interface. UBNT(config)# interface swp54
UBNT(config-if)# mtu 9216
UBNT(config-if)# exit
SW(config)# interface fa1/0
SW(config-if)# ip mtu 9216
SW(config-if)# end

LAG (Link Aggregation) Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Display LACP internal information. UBNT# show lacp internal
SW# show lacp internal
Display the status of a port-channel interface. UBNT# show interface po1
SW# show interface port-channel 1
Display the traffic statistics for port channels. UBNT# show lacp counters
SW# show lacp counters
Clear LACP counters. UBNT# clear lacp counters
SW# clear lacp counters
Display the LACP system identifier. UBNT# show lacp sys-id
SW# show lacp system-identifier
Display information about the LACP neighbor. UBNT# show lacp neighbor
SW# show lacp neighbor
Configure the LACP system-priority and priority for the physical interface. UBNT(config)# lacp system-priority 65535
UBNT(config)# interface swp54
UBNT(config-if)# lacp port-priority priority 20000
UBNT(config-if)# exit
SW(config)# lacp system-priority 65535
SW(config)# interface fa1/0
SW(config-if)# lacp port-priority priority 20000
SW(config-if)# exit

  • Specify the port mode as active for the links in a port channel.
  • Define the minimum and maximum number of active bundled.
  • Define LACP ports allowed in a port channel.
UBNT(config)# interface swp1
UBNT(config-if)# no switchport
UBNT(config-if)# channel-group 1 mode active
UBNT(config-if)# interface swp2
UBNT(config-if)# no switchport
UBNT(config-if)# channel-group 1 mode active
UBNT(config-if)# interface port-channel 1
UBNT(config-if)# lacp min-links 2
UBNT(config-if)# lacp max-bundle 8
UBNT(config-if)# exit
SW(config)# interface fa0/1
SW(config-if)# channel-group 1 mode active
SW(config-if)# interface fa0/2
SW(config-if)# channel-group 1 mode active
SW(config-if)# interface port-channel 1
SW(config-if)# lacp min-links 2
SW(config-if)# lacp max-bundle 8
SW(config-if)# exit
Delete all interfaces from port-channel interface. UBNT(config-if)# int po1
UBNT(config-if)# delete all-lag-members
UBNT(config-if)# exit
NA

SPAN (Port Mirroring) Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Display information about the Switched Port Analyzer (SPAN). UBNT# show mirror
SW# show monitor session
Set up a SPAN session (session 1) for monitoring ingress & egress port traffic to a destination port. UBNT(config)# mirror tx session 1
UBNT(config-mirror)# source interface swp1
UBNT(config-mirror)# destination interface swp2
UBNT(config)# mirror rx session 1
UBNT(config-mirror)# source interface swp1
UBNT(config-mirror)# destination interface swp2
UBNT(config-mirror)# exit
SW(config)# monitor session 1 source interface fastEthernet0/1 tx
SW(config)# monitor session 1 source interface fastEthernet0/1 rx
SW(config)# monitor session 1 destination interface fastEthernet0/2
Delete SPAN sessions. UBNT(config)# no mirror tx session 1
UBNT(config)# no mirror rx session 1
SW(config)# no monitor session 1

Storm Control Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Display storm control statistics for specified interface. UBNT# show statistics storm-control interface swp1
SW# show interface fa0/1 counters storm-control
Traffic Storm Control Configuration (level as a percentage of the total interface bandwidth). UBNT(config)# interface swp1
UBNT(config-if)# storm-control unicast level 50
UBNT(config-if)# storm-control multicast level 50
UBNT(config-if)# storm-control broadcast level 50
UBNT(config-if)# exit
SW(config)# interface fa0/1
SW(config-if)# storm-control unicast level 50
SW(config-if)# storm-control multicast level 50
SW(config-if)# storm-control broadcast level 50
SW(config-if)# exit

Port Isolation (Protected Port) Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Display protected port state for specific interface. UBNT# show interface swp1 switchport
SW# show interface fa0/1 switchport
Enable or disable the interface that will be a protected port. UBNT(config)# interface swp1
UBNT(config-if)# switchport protected
UBNT(config-if)# no switchport protected
UBNT(config-if)# exit
SW(config)# interface fa0/1
SW(config-if)# switchport protected
SW(config-if)# no switchport protected
SW(config-if)# exit

Flow Control Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

*Display the flow control settings.
 NA
SW# show interface flowcontrol
  • Configure flow-control mode
  • Configure flow-control priority
UBNT(config)# interface swp1
UBNT(config-if)# flow-control mode both
UBNT(config-if)# priority-flow-control mode both
UBNT(config-if)# exit
SW(config)# interface ethernet fa0/1
SW(config-if)# flowcontrol receive on
SW(config-if)# flowcontrol send on
SW(config-if)#priority-flow-control mode on
SW(config-if)# exit
Disable Link Level Flow Control and its priority on a specific interface. UBNT(config)# interface swp1
UBNT(config-if)# no flow-control
UBNT(config-if)# no priority-flow-control
UBNT(config-if)# exit
SW(config)# interface ethernet fa0/1
SW(config-if)# flowcontrol receive off
SW(config-if)# flowcontrol send off
SW(config-if)#priority-flow-control mode off
SW(config-if)# exit

QoS (Scheduling, Shaping and Policing) Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Verify existing scheduling policy, queues weight, and bound interfaces. UBNT# show qos policy scheduling SW# show mls qos interface queueing
Verify existing shaping policy. UBNT# show qos policy shape
SW# show policy-map interface
Verify existing policing policy. UBNT# show qos policy policing
Configure the QoS Scheduling policy, binding the policy to a specific interface. UBNT(config)# qos policy scheduling sch_pol
UBNT(qos-policy)# queue 0 dwrr 5
UBNT(qos-policy)# queue 1 dwrr 10
UBNT(qos-policy)# queue 2 dwrr 20
UBNT(qos-policy)# queue 3 dwrr 30
UBNT(qos-policy)# queue 4 dwrr 40
UBNT(qos-policy)# queue 5 dwrr 50
UBNT(qos-policy)# queue 6 dwrr 60
UBNT(qos-policy)# queue 7 dwrr 70
UBNT(qos-policy)# exit
UBNT(config)# interface swp1
UBNT(config-if)# qos policy scheduling sch_pol
UBNT(config-if)# exit
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# wrr-queue bandwidth 5 10 20 30 40 50 60 70
SW(config-if)# exit
Configure the QoS Shaping policy, binding the policy to a specific interface. UBNT(config)# qos policy shape shape_pol
UBNT(qos-policy)# queue 0 min 2000 64000 max 10000 640000
UBNT(qos-policy)# queue 1 min 2000 64000 max 20000 640000
UBNT(qos-policy)# queue 2 min 2000 64000 max 20000 640000
UBNT(qos-policy)# queue 3 min 2000 64000 max 30000 640000
UBNT(qos-policy)# queue 4 min 2000 64000 max 40000 640000
UBNT(qos-policy)# queue 5 min 2000 64000 max 50000 640000
UBNT(qos-policy)# queue 6 min 2000 64000 max 60000 640000
UBNT(qos-policy)# queue 7 min 2000 64000 max 70000 640000
UBNT(qos-policy)# exit
UBNT(config)# interface swp1
UBNT(config-if)# qos policy shape shape_pol
UBNT(config-if)# end
SW(config)#policy-map shape_pol
SW(config-pmap)#class shape_cl
SW(config-pmap-c)#shape avarage 640000
SWconfig-pmap-c)# exit
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)#service-policy output shape_pol
SW(config-if)# exit
*Configure the QoS Policing policy that utilizes two ACLs (associated with policer), binding the policy to a specific interface. UBNT(config)# ip access-list voice-acl
UBNT(config-ip-acl)# 10 permit ip 192.168.10.0/24 any
UBNT(config-ip-acl)# exit
UBNT(config)# ip access-list database
UBNT(config-ip-acl)# 10 permit tcp any any eq 1810
UBNT(config-ip-acl)# 20 permit tcp any any eq 2481
UBNT(config-ip-acl)# 30 permit tcp any any eq 1521
UBNT(config-ip-acl)# exit
UBNT(config)# policer aggregate voice-acl-aggr
UBNT(qos-policer)# conform-action transmit
UBNT(qos-policer)# exit
UBNT(config)# policer aggregate database-aggr
UBNT(qos-policer)# conform-action set-dscp 18
UBNT(qos-policer)# exit
UBNT(config)# qos policy policing test-policing
UBNT(qos-policy-policing)# 10 access-list voice-acl
UBNT(qos-policy-policing-acl)# policer voice-acl-aggr
UBNT(qos-policy-policing-acl)# exit
UBNT(qos-policy-policing)# 20 access-list database
UBNT(qos-policy-policing-acl)# policer database-aggr
UBNT(qos-policy-policing-acl)# exit
UBNT(qos-policy-policing)# exit
UBNT(config)# interface swp1
UBNT(config-if)# qos policy policing test-policing input
UBNT(config-if)# end
SW(config)#ip access-list extended voice-acl
SW(config-ext-nacl#permit ip 192.168.10.0 0.0.0.255 any
SW(config-ext-nacl)#exit
SW(config)#ip access-list extended database
SW(config-ext-nacl)#permit tcp any any eq 1810
SW(config-ext-nacl)#permit tcp any any eq 2481
SW(config-ext-nacl)#permit tcp any any eq 1521
SW(config-ext-nacl)#exit
SW(config)#class-map class-voice
SW(config-cmap)#match access-group name voice-acl
SW(config-cmap)#exit
SW(config)#class-map class-database
SW(config-cmap)#match access-group name database
SW(config-cmap)#exit
SW(config)#policy-map test-policing
SW(config-pmap)#class class-voice
SW(config-pmap-c)#trust cos
SW(config-pmap-c)#exit
SW(config-pmap)#class class-database
SW(config-pmap-c)#set dscp af21
SW(config-pmap-c)#exit
SW(config-pmap)#exit
SW(config)#interface gigabitEthernet 1/0/1
SW(config-if)#service-policy input test-policing
SW(config-if)#exit
Unbind the scheduling, shaping and policing policies from a specific interface. UBNT(config)# interface swp1
UBNT(config-if)# no qos policy scheduling
UBNT(config-if)# no qos policy shape
UBNT(config-if)# no qos policy policing input
UBNT(config-if)# exit
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# no wrr-queue bandwidth
SW(config-if)# no service-policy output shape_pol
SW(config-if)# no service-policy input test-policing
SW(config-if)# exit

ACL Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Show the MAC access list configuration. UBNT# show access-lists mac-acl SW# show mac access-lists mac-acl
Show the IP access list configuration. UBNT# show access-lists ip-acl SW# show ip access-lists ip-acl
*MAC ACL Configuration UBNT(config)# mac access-list mac-acl
UBNT(config-mac-acl)# 10 permit any 0000.aaaa.0001 ffff.ffff.ffff any
UBNT(config-mac-acl)# 20 permit any 0000.aaaa.0002 ffff.ffff.ffff any
UBNT(config-mac-acl)# no sequence 20
UBNT(config-mac-acl)# exit
SW(config)#mac access-list extended mac-acl
SW(config-ext-macl)#permit any host 0000.aaaa.0001
SW(config-ext-macl)#permit any host 0000.aaaa.0002
SW(config-ext-macl)#no permit any host 0000.aaaa.0002
SW(config-ext-macl)#exit
IP ACL Configuration SW(config)# ip access-list ip-acl
SW(config-ip-acl)# 10 permit ip 192.168.10.0/24 any
SW(config-ip-acl)# 20 deny tcp any any eq 8080
SW(config-ip-acl)# exit
SW(config)#ip access-list extended ip-acl
SW(config-ext-ipacl)#permit ip 192.168.10.0 0.0.0.255 any
SW(config-ext-ipacl)#deny tcp any any eq 8080
SW(config-ext-ipacl)#exit
Apply MAC ACL and IP ACL to the specific interface. UBNT(config-mac-acl)# interface swp1
UBNT(config-if)# mac access-group mac-acl in
UBNT(config-if)# ip access-group ip-acl in
UBNT(config-mac-acl)# exit
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# mac access-group mac-acl in
SW(config-if)# ip access-group ip-acl in
SW(config-if)# exit
Remove MAC ACL and IP ACL from the specific interface. UBNT(config-mac-acl)# interface swp1
UBNT(config-if)# no mac access-group in
UBNT(config-if)# no ip access-group in
UBNT(config-mac-acl)# exit
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# no mac access-group mac-acl in
SW(config-if)# no ip access-group ip-acl in
SW(config-if)# exit

STP; RSTP Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Display Spanning Tree information. UBNT# show spanning-tree stp SW# show spanning-tree
Display a brief summary about STP. UBNT# show spanning-tree interface brief SW# show spanning-tree brief
Display the STP interface status and configuration of specified interface. UBNT# show spanning-tree interface swp1 SW# show spanning-tree interface gigabitEthernet 1/0/1
Display Rapid Spanning Tree information. UBNT# show spanning-tree rstp SW# show spanning-tree
Configure Spanning Tree Properties. UBNT(config)# spanning-tree
UBNT(config)# spanning-tree mode stp
UBNT(config)# spanning-tree priority 32768
UBNT(config)# spanning-tree forward-time 15
UBNT(config)# spanning-tree max-age 20
UBNT(config)# spanning-tree hello-time 2
UBNT(config)# spanning-tree transmit hold-count 4
UBNT(config)# spanning-tree pathcost-method long
UBNT(config)# exit
SW(config)# spanning-tree
SW(config)# spanning-tree mode stp
SW(config)# spanning-tree priority 32768
SW(config)# spanning-tree forward-time 15
SW(config)# spanning-tree max-age 20
SW(config)# spanning-tree hello-time 2
SW(config)# spanning-tree transmit hold-count 4
SW(config)# spanning-tree pathcost-method long
SW(config)# exit
Specify that the Rapid STP is enabled. UBNT(config)# spanning-tree mode rstp SW(config)# spanning-tree mode rstp
Disable Spanning Tree globally. UBNT(config)# no spanning-tree SW(config)#no spanning-tree
*Enable or disable BPDU Guard for an interface. UBNT(config)# interface swp1.1
UBNT(config-if)# spanning-tree bpdu-guard
UBNT(config-if)# no spanning-tree bpdu-guard
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# spanning-tree bpduguard enable
SW(config-if)# spanning-tree bpduguard disable
*Enable or disable Loop Guard for an interface. UBNT(config)# interface swp1.1
UBNT(config-if)# spanning-tree loopback-detection
UBNT(config-if)# no spanning-tree loopback-detection
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# spanning-tree loopguard default
SW(config-if)# no spanning-tree loopguard default
*Enable or disable Root Guard for an interface. UBNT(config)# interface swp1.1
UBNT(config-if)# spanning-tree root-guard
UBNT(config-if)# no spanning-tree root-guard
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# spanning-tree guard root
SW(config-if)# no spanning-tree guard root

MSTP Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Display Multiple Spanning Tree configuration information. UBNT# show spanning-tree mst configuration SW# show spanning-tree mst configuration
Display Multiple Spanning Tree specific instance information. UBNT# show spanning-tree mst 1 status SW# show spanning-tree mst 1
Displays a brief summary about specific MSTP instance. UBNT# show spanning-tree mst 1 interface brief  
Configure Multiple Spanning Tree Properties. UBNT(config)# spanning-tree mode mst
UBNT(config)# spanning-tree mst max-hops 22
UBNT(config)# spanning-tree mst name test_inst
UBNT(config)# spanning-tree mst revision 32768
SW(config)# spanning-tree mode mst
SW(config)# spanning-tree mst max-hops 22
SW(config)# spanning-tree mst configuration
SW(config-mst)# name test_inst
SW(config-mst)# revision 32768
SW(config-mst)# exit
Configure instance priority, and add VLAN 100 to MST instance 2. UBNT(config)# spanning-tree mst 2 priority 61440
UBNT(config)# spanning-tree instance 2 domain 100
SW(config)# spanning-tree mst 2 priority 61440
SW(config)# spanning-tree mst configuration
SW(config-mst)# instance 2 vlan 100
SW(config-mst)# exit
*STP/MSTP interface related commands for special interface(swp1) in specific vlan(100). UBNT(config-if)# interface swp1.100
UBNT(config-if)# spanning-tree link-type point-to-point
UBNT(config-if)# spanning-tree cost 10000
UBNT(config-if)# spanning-tree port-priority 32
UBNT(config-if)# spanning-tree edge-port
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# spanning-tree link-type point-to-point
SW(config-if)# spanning-tree mst <instance-id> port-priority 32
SW(config-if)# spanning-tree mst <instance-id> cost 10000
SW(config-if)# spanning-tree portfast

Port Error Disable / Auto Recovery Commands

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Display the time period after which the interfaces are enabled for 'errdisable' conditions. UBNT# show errdisable recovery SW# show errdisable recovery
Display the reason for the 'errdisable' status. UBNT# show errdisable detect SW# show errdisable detect
Configure 'errdisable' recovery interval. UBNT(config)# errdisable recovery interval 400 SW(config)# errdisable recovery interval 400
*Enable or disable the BPDU guard 'errdisable' recovery condition. UBNT(config)# errdisable recovery cause bpduguard
UBNT(config)# no errdisable recovery cause bpduguard
SW(config)# errdisable recovery cause bpduguard
SW(config)# no errdisable recovery cause bpduguard

DHCP Guard / DHCP Snooping (Cisco)

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Display DHCP guard settings. UBNT# show ip dhcp guard SW# show ip dhcp snooping binding
Enable or disable DHCP Guard. UBNT(config)# ip dhcp guard
UBNT(config)# no ip dhcp guard
SW(config)# ip dhcp snooping
SW(config)# no ip dhcp snooping
Add or remove trusted DHCP server to special VLAN (Cisco uses the trust interface approach). UBNT(config)# ip dhcp guard vlan 23 server 172.16.1.1
UBNT(config)# no ip dhcp guard vlan 23 server 172.16.1.1
SW(config)# ip dhcp snooping vlan 23
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# ip dhcp snooping trust
SW(config-if)# no ip dhcp snooping trust

ARP

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Display ARP table. UBNT# show arp SW# show ip arp
Configure ARP aging time globally and per specific interface. UBNT(config)# arp aging-time 300
UBNT(config)# int swp1
UBNT(config-if)# arp aging-time 3600
UBNT(config-if)# exit
SW(config)# arp timeout 300
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# arp timeout 3600
SW(config-if)# exit
Add or remove static ARP entry. UBNT(config)# ip arp 10.1.1.1 44:d9:e7:9e:b6:db port swp1
UBNT(config)# no ip arp 10.1.1.1 44:d9:e7:9e:b6:db
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# ip arp 10.1.1.1 44:d9:e7:9e:b6:db
SW(config-if)# no ip arp 10.1.1.1 44:d9:e7:9e:b6:db
Clear the ARP table. UBNT# clear arp all SW# clear ip arp

DHCP Client/Static IP

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Overview all IPv4 interfaces on the switch. UBNT# show ip interface brief SW# show ip interface brief
Enable/Disable DHCP Client on bridge-domain interface. UBNT(config)# interface bridge 1
UBNT(config-if)# ip address dhcp
UBNT(config-if)# no ip address dhcp
UBNT(config-if)# exit
SW(config)# interface vlan1
SW(config-if)# ip address dhcp
SW(config-if)# no ip address dhcp
SW(config-if)# exit
Configure/Remove static IP address on interface. UBNT(config)# interface swp1
UBNT(config-if)# ip address 172.16.0.1/24
UBNT(config-if)# no ip address 172.16.0.1/24
UBNT(config-if)# exit
SW(config)# interface gigabitEthernet 1/0/1
SW(config-if)# ip address 172.16.0.1 255.255.255.0
SW(config-if)# no ip address 172.16.0.1
SW(config-if)# exit

IP Route(Static)

Back to Top

Command Description

USW-Leaf Command

Cisco Command

Display IPv4 routing table. UBNT# sh ip route SW# show ip route
Configure/Remove default static route. UBNT(config)# ip route 0.0.0.0/0 192.168.1.1
UBNT(config)# no ip route 0.0.0.0/0 192.168.1.1
SW(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.1
SW(config)# no ip route 0.0.0.0 0.0.0.0 192.168.1.1
Configure/Remove static route to specific network. UBNT(config)# ip route 172.16.1.0/24 192.168.1.1
UBNT(config)# no ip route 172.16.1.0/24 192.168.1.1
SW(config)# ip route 172.16.1.0 255.255.255.0 192.168.1.1
SW(config)# no ip route 172.16.1.0 255.255.255.0 192.168.1.1
Configure static route with administrative distance. UBNT(config)# ip route 172.16.1.0/24 192.168.1.1 15 SW(config)# ip route 172.16.1.0 255.255.255.0 192.168.1.1 15
Configure/Remove null0(blackhole) route. UBNT(config)# ip route 172.16.1.0/24 null0
UBNT(config)# no ip route 172.16.1.0/24 null0
SW(config)# ip route 172.16.1.0 255.255.255.0 null0
SW(config)# no ip route 172.16.1.0 255.255.255.0 null0
Configure/Remove ICMP reject route. UBNT(config)# ip route 172.16.1.0/24 reject
UBNT(config)# no ip route 172.16.1.0/24 reject
NA
Was this article helpful?
8 out of 9 found this helpful
Can't find what you're looking for?
Visit our worldwide community of Ubiquiti experts for more answers
Visit the Ubiquiti Community