This article explains in depth a simple process that in most cases will be a matter of powering up the new access point, waiting a few minutes for it to appear in the Devices screen of the UniFi Network Controller, clicking on it and then clicking Adopt (or Upgrade, then Adopt).
Most of the settings discussed in this article will already be configured correctly and as long as the UAP broadcasting signal, and the one receiving it to create the wireless uplink are not legacy access points, the requirements and other topics touched on this article are not something to worry about.
Table of Contents
- How it Works
- Compatibility Matrix
- How to Configure Wireless Uplink
- Best Practices
- Related Articles
Wireless Uplink allows an access point with a wired data connection to act as a Base Station (Uplink AP) for up to four other access points on 5GHz (or 2.4GHz for some legacy APs), which can extend Wi-Fi coverage to inaccessible areas, as well as pull down any configuration and settings changes from the UniFi Network Controller via the upstream AP.
To understand how the wireless uplink feature can be used, it's important to know the terms used in UniFi/this article:
Base Station (Uplink AP): Access point with a wired data connection that is configured to relay data to and from Mesh APs (Downlink AP).
Mesh APs (Downlink AP): Access point without wired data connection, that functions as a normal wired AP would by sending/receiving client data wirelessly to/from the base station, or an intermediate AP by use of the wireless uplink feature. Is sometimes also called "island" AP.
Multi-hop Wireless Uplink: A deployment that uses a base station but has more than one level of wireless uplink with intermediate APs relaying data to and from the base station. When using multiple levels of APs, the uplink tiers can be referred to by root (base station), first hop, second hop, etc. See the example below:
How it Works
Once enabled, the wireless uplink feature allows access points without a wired data connection to communicate with pre-configured wired access points on a network. This offers a number of benefits:
- Factory default or unadopted devices that have been powered up via PoE can connect to an AP in range and make itself available for adoption within the UniFi Network Controller.
- These devices can be adopted and configured in the controller via the Wireless Uplink connection.
- Once configured, these devices can broadcast SSIDs and relay network traffic to and from the network through the uplinked AP.
- Additional devices without a wired data connection can be booted up and installed via wireless uplink by communicating with a first hop AP.
- In order to use the wireless uplink feature, the wireless uplink option must be enabled. In the UniFi Network Controller, navigate to Settings > Site > Services section and make sure the checkbox "Enable wireless uplink" is checked for the Uplink Connectivity Monitor setting.
- Two different meshing settings must be enabled for the uplink and downlink APs:
- The "Allow meshing to another access point" option must be enabled on the Mesh (downlink) Access Point. Enable it by clicking on the access point in the Devices tab to open the AP properties panel, then navigate to Configuration > Wireless Uplink. Enable this on a mesh (downlink) AP also only when using it for a multi-hop; in other words when this mesh AP is the uplink of another mesh AP.
- The "Allow meshing from other access points" option must be enabled on the base station (uplink). Enable it by clicking on the access point in the Devices tab to open the AP properties panel, then navigate to Configuration > Radios. You can choose to enable it for only one radio, or for both the 2G and 5G radios.
- At least one wired access point must support wireless uplink (see compatibility matrices below.)
- A power source for non-data wired AP i.e. PoE injector.
- (Recommended) Most current stable firmware.
Certain models are able to use 2.4GHz, while most use 5GHz by default. Keep the following guidelines in mind:
|Dual band base station AP to dual-band mesh AP: will uplink on 5GHz.|
|Dual band base station AP to single band mesh AP: will uplink on the supported frequency of the single band model.|
|Single band base station AP to single band mesh AP: will uplink, as long as the same band is supported on both sides of the link.|
|Single band (2.4GHz only models) base station AP to dual-band mesh AP will not be able to uplink.|
- Single band APs can act as a base station only within the band in which they operate
- Dual band APs can act as a base station in 2.4GHz for legacy single-band access points, and 5GHz for all others.
- Dual band APs can act as a mesh AP only in the 5GHz band.
See the following compatibility tables for information on supported devices. Starting on UniFi AP firmware v.3.9.1 all current (non-legacy) UAPs support wireless uplink, as well as multi-hop wireless uplink.
Supports Wireless Uplink
Supports Multi-hop Wireless Uplink
*Support for non-Mesh non-legacy APs has been added in AP firmware v.3.9.1 and later.
Supports Wireless Uplink
Supports Multi-hop Wireless Uplink
How to Configure Wireless Uplink
If the wirelessly connected access point doesn't appear, then connect it via Ethernet cable, upgrade to newest firmware version if applicable and proceed to adopt it while wired. Once adopted, disconnect it from Ethernet (but not power) and wait a few minutes while it goes through a few statuses (heartbeat missed, isolated, etc) and then appears as Connected (Wirelessly).
If neither of these methods work, then you should proceed and verify the settings discussed in this article.
Enabling Wireless Uplink:
1. Open your UniFi Network Controller.
2. In the Classic Settings mode, go to Settings > Site > Services section. If using New Settings mode, find this option within System Settings > Controller Configuration > Uplink Connectivity Monitor.
3. Make sure the checkbox "Enable wireless uplink" is checked for the Uplink Connectivity Monitor setting. Or in New Settings, that the Enable Uplink Connectivity Monitor toggle is ON.
Adopting Devices via Wireless Uplink:
1. Power up the mesh access point that will be communicating with the Base Station (uplink) AP via wireless uplink and ensure it is within range of the Base Station. A source of PoE will be needed to power the device without a wired data connection.
2. After the device boots up, it will appear within the Devices page of your Controller, with the status "Pending Adoption (Wireless)".
3. Click "Adopt" to adopt the device.
4. Once the adoption has begun, the base station will provision, then again show as connected. After this, the Mesh AP device status will change with each step of the process:
- And when finished, Online (Wireless).
- After device boots up, it will appear within the Devices page of your controller, with the status Pending Adoption (Wireless).
This process will take longer than a wired adoption, it should take roughly 2-3 minutes to show up as adopted within your Controller. Once the adoption has finished your device can be managed within the UniFi Controller in the same way as a wired access point.
Configuring/Modifying Existing Wireless Uplink Connections
Occasionally, administrators may want to change the way in which their Wireless Uplink devices are communicating, for instance, changing one AP to use a different uplink. This can all be easily done through the UniFi Controller. To do this:
1. Open your UniFi Network Controller and navigate to the Devices section.
2. Click on the device that you'd like to configure.
3. Click on the Configuration Tab in the Device Pane.
4. Select “Wireless Uplinks”
5. Select the desired AP to act as uplink, and click the link icon.
6. Manually configuring the uplink priority is also available for configuration. This allows for having a primary wireless uplink connection, but in the case that the uplink priority degrades or is insufficient, the second priority uplink will be used. To see and set Priority 1 and Priority 2, make sure to have the option of "Manually configure the uplink priorities" enabled.
To remove the existing uplink:
1. Open the device configuration pane for the UAP acting as the wired base station, go to Details > Downlinks, and click the trash icon next to the undesired uplink connection.
2. The device will then re-provision and will no longer use the selected AP as an uplink base.
Using Maps/Topology Views
The Maps and Topology views are very helpful ways to manage your Wireless Uplink configuration as they help visualize the deployment. Carefully labeling devices and placing them in the appropriate location on your map can help save a lot of time when managing a Wireless Uplink deployment.
To access these views:
1. Open the UniFi Network Controller.
2. Navigate to the Map section using the navigation bar on the left.
3. Select either Maps or Topology from the dropdown menu in the top left of the display.
Once in this view, managing a device is possible by clicking on the device and clicking the configuration icon. Learn more about how to use the Map section in the UniFi User Guide, Chapter 6: Map.
The wireless uplink feature is most helpful in extending network access to less accessible physical locations within the network. When LAN connectivity is not viable in a particular location/setting, wireless uplink can help take your network wherever it is needed. The Mesh product line can be particularly helpful in extending the network with multi-hop functionality and an outdoor-suitable enclosure.
Also, to ensure that network speeds are optimized with a wireless uplink, we recommend when designing a network to balance the wireless uplink load from wired APs (base stations) as to not create unnecessary delays on any devices connected via the overused AP. See example below:
Note the example on the left has not balanced the load between the two UAP-AC-MESH and is unnecessarily burdening the one AP when the other could also be used as a Wireless Uplink AP, as has been done on the better example on the right. Also, the first example on the left added an unnecessary level of Wireless Uplink- while the example on the right eliminated this.
Unless your network needs to use wireless uplink or benefits from the use of this feature, we recommend you disable the Connectivity Uplink Monitor & Wireless Uplink setting. To do so, in your UniFi Network Controller:
1. Go to the Settings section using the navigation menu on the left.
2. Go to Site.
3. Under "Uplink Connectivity Monitor", uncheck the box next to "Enable connectivity monitor and wireless uplink". Click Apply Changes.
Disabling this setting can offer some improved speed and is often suggested when network speeds with UniFi are less than ideal.
Selecting Bands Depending on UAP Generation
Remember that if you have several wired APs, these APs should have assigned channels that are different and do not overlap with other AP channels to minimize interference. See what generation each UAP model is in our UniFi Generation Matrix.
Wireless Uplink with all Gen 2 or Gen 3 UAP(s)
Set the wired UAP to static on 5GHz and to a static on 2.4GHz (1, 6 or 11 making sure it's not a band also set for any of the other UAPs) leave the wireless uplinked UAP(s) set to AUTO on the 5GHz radio and set a static channel on 2.4GHz not shared by others.
Wireless Uplink with all Gen 1 UAP(s)
Set the wired UAP to a static channel on 2.4GHz, leave the wireless uplinked UAP(s) set to AUTO on 2.4GHz.
Wireless Uplink from Gen 1 UAP(s) to Gen 2 or Gen 3 UAP(s)
Set the wired UAP to a static channel on 2.4GHz ( and 5GHz if you’re wireless uplinking Generation 2/3 UAP(s) as well ), leave the wireless uplinked UAP(s) set to AUTO.